Audiopedia

Random Articles

Receiver

A combination of a power amplifier, preamplifier and tuner. In later years, it may additionally contain a surround… Edit »
Audiophile-Wiki

The Audiophile Wiki is a free resource for audiophiles to share their knowledge. Launched on May 27th, 2008, the… Edit »
Wow-and-Flutter

Wow and flutter measurement is carried out on audio tape machines, cassette recorders and players, and other analog recording… Edit »
DLNA

The Digital Living Network Alliance is an international, cross-industry collaboration of consumer electronics, computing… Edit »
asynchronous-clock

In a digital audio system and asynchronous clock is an isolated time base that is unrelated to the central system. … Edit »

See all Audiopedia articles

Search the Audiopedia

Add an Article

Quick Links

Browse all Audiopedia Articles Browse Categories Upload a Picture View Uploaded Pictures Audiopedia Help

View View Source: balanced

You are not allowed to edit this page.

Balanced audio is a term used to describe a signal transmission method using two signals in the same cable of opposite polarity.  The main purpose of balanced audio connections is to reduce noise both from external sources as well as internal sources that are common to the two signals.

The balanced signals are typically sent over balanced interconnects through [[XLR]] connectors.

Balanced audio connections use a number of techniques to reduce noise.

A typical balanced cable contains two identical wires, which are twisted together and then wrapped with a third conductor (foil or braid) that acts as a shield.

The term "balanced" comes from the method of connecting each wire to identical impedances at source and load. This means that much of the electromagnetic interference will induce an equal noise voltage in each wire. Since the amplifier at the far end measures the difference in voltage between the two signal lines, noise that is identical on both wires is rejected. The noise received in the second, inverted line is applied against the first, upright signal, and cancels it out when the two signals are subtracted.

This [[differential signal]] recombination can be implemented with a differential amplifier. A balun may also be used instead of an active differential amplifier device.

The wires are also twisted together, to reduce interference from electromagnetic induction. A twisted pair makes the loop area between the conductors as small as possible, and ensures that a magnetic field that passes equally through adjacent loops will induce equal levels of noise on both lines, which is canceled out by the differential amplifier. If the noise source is extemely close to the cable, then it is possible it will be induced on one of the lines more than the other, and it won't be canceled as well, but canceling will still occur to the extent of the amount of noise that is equal on both lines.

The separate shield of a balanced audio connection also yields a noise rejection advantage over an unbalanced two-conductor arrangement (such as used in typical home stereos) where the shield must also act as the signal return wire. Any noise currents induced into a balanced audio shield will not therefore be directly modulated onto the signal, whereas in a two-conductor system they will be. This also prevents ground loop problems, by separating the shield/chassis from signal ground.

[b]Differential signalling[/b]

Signals are often transmitted over balanced connections using the differential mode, meaning the wires carry signals of opposite polarity to each other (for instance, in an XLR connector, pin 2 carries the signal with normal polarity, and pin 3 carries an inverted version of the same signal).

Despite popular belief, this is not necessary for noise rejection. As long as the impedances are balanced, noise will couple equally into the two wires (and be rejected by a differential amplifier), regardless of the signal that is present on them.[1][2] A simple method of driving a balanced line is to inject the signal into the "hot" wire through a known source impedance, and connect the "cold" wire to ground through an identical impedance. Due to common misconceptions about differential signalling, this is often referred to as a quasi-balanced or impedance-balanced output, though it is, in fact, fully balanced and will reject common-mode interference.

There are some benefits to driving the line with a fully differential output, though:

    * The electromagnetic field around a differential line is ideally zero, which reduces crosstalk into adjacent cables.
    * Though the signal level would not be changed due to nominal level standardization, the maximum output from the differential drivers is twice as much, giving 6 dB extra headroom.[1] (if the amplifiers are identical, though, their output noise sums to 3 dB more than a single amplifier, decreasing dynamic range).
    * Noise that is correlated between the two amps (from poor power supply rejection, for instance), would be cancelled out.
    * At higher frequencies, the output impedance of the output amplifier can change, resulting in a small imbalance. When driven in differential mode by two identical amplifiers, this impedance change will be the same for both lines, and thus cancelled out.[1]
    * Differential drivers are also more forgiving of incorrectly wired adapters or equipment that unbalances the signal by shorting pin 2.[1]

[b]Internally balanced audio design[/b]

Most professional audio products (recording, public address, etc.) provide differential balanced inputs and outputs, typically via XLR or TRS connectors. However, in most cases, a differential balanced input signal is internally converted to a single-ended signal via transformer or electronic amplifier. After internal processing, the single-ended signal is converted back to a differential balanced signal and fed to an output. A small number of professional audio products have been designed as an entirely differential balanced signal path from input to output; the audio signal never unbalances. This design is achieved by providing identical (mirrored) internal signal paths for both pin 2 and pin 3 signals (AKA "hot" and "cold" audio signals). In critical applications, a 100% differential balanced circuit design can offer better signal integrity by avoiding the extra amplifier stages or transformers required for front-end unbalancing and back-end rebalancing. Fully balanced internal circuitry has been promoted as yielding 3dB better dynamic range.

Top

Audiopedia

Random Articles

Receiver

Audiophile-Wiki

Wow-and-Flutter

DLNA

asynchronous-clock

Search the Audiopedia

Add an Article

Quick Links

View View Source: balanced

Explore

PS Newsletter

Discussion Forums

GlobalNet

Reviews

Knowledge Base

Tech Tips

How To

AV News